Skip to content
NEXGY — Next Generation Energy

Technology

How is a battery storage system monitored and controlled remotely?

Through a layered control stack. The battery management system watches the cells, the energy management system decides when to charge and discharge, and a SCADA (supervisory control and data acquisition) system collects plant data every minute or faster, raises alarms, and exchanges data and setpoints with the remote operator and the state or regional load despatch centre.

Published 7 November 2026 · Last updated 7 November 2026 · 5 min read · By NEXGY Research Desk

On this page

A utility-scale battery is often in a field nobody visits daily. Yet it must respond to the grid in seconds, report its condition every minute, and be stopped instantly if anything goes wrong.

That is the job of the remote monitoring and control stack, and at its top sits SCADA, short for supervisory control and data acquisition.

This guide explains what SCADA does in a battery energy storage system (BESS), how it fits with the other control layers, and what Indian tenders actually ask for.

Four layers, four jobs

Battery control is easiest to understand as a stack. Each layer has a narrower or wider view of the world.

  • BMS (battery management system) looks inward at the cells. It measures voltage, current and temperature and will shut the battery down if a limit is crossed. Our guide to the BMS covers this layer.
  • EMS (energy management system) decides what the battery should do commercially: when to charge, when to discharge, and how hard. The split between these two is explained in EMS vs BMS.
  • PPC (power plant controller) controls the plant as one unit at the grid connection point. In the SECI specification we reviewed, the PPC “shall communicate with EMS for BESS inverter control” and uses voltage and current at the point of interconnection as its reference.
  • SCADA gathers data from every device, shows it to operators, stores it, raises alarms, and exchanges data and setpoints with the grid operator.
Who talks to whomSLDC / RLDCtelemetry, schedules, AGCRemote operationscloud mirror, 10+ usersPlant SCADAlogging, alarms, operator screensPower plant controller (grid point)EMS (dispatch decisions)BMS + inverters + metersSECI spec figuresPolling: ≤ 1 minuteFault alarms: < 5 secondsPlant server: 2 years of dataField buffer: ≥ 2 weeksClock: GPS time-syncCyber: CEA 2021 guidelines
The control stack of a grid-scale battery, with the polling, alarm and data-retention figures from a recent SECI BESS technical specification.

What SCADA actually records

The technical specification attached to a recent SECI 600 MW / 1,200 MWh BESS tender gives a useful picture of what a utility buyer expects. It asks SCADA to provide real-time data logging of:

  • Imported and exported power (MW) and energy (kWh)
  • State of charge (SoC) and state of health (SoH) for each container
  • Maximum and minimum temperatures
  • Auxiliary system status, run hours and equipment status
  • Key performance indicators, alarms and events

It also requires time-stamped fault logging and sequence of event reports, which put every trip and alarm in the order it happened. After an incident, that record is how you work out what failed first.

How fast, and how long

Speed and memory matter as much as the list of data points. The same SECI specification sets clear numbers:

RequirementSECI specification
Polling of containers, inverters, meters, transformers, switchgearNo more than one minute
Fault alarm deliveryUnder five seconds
Plant server data storageTwo years, with a redundant server
Local buffering in field controllersAt least two weeks
Remote/cloud accessMirror of plant data, at least 10 concurrent users
Time referenceGPS-synchronised clock for all devices

The two-week local buffer is the detail buyers most often miss. Network links at remote sites fail. If the field controllers cannot hold data until the link returns, you lose the record. That gap can then become a dispute over your availability guarantee.

Talking to the grid operator

A grid-connected battery is not only watched by its owner. The grid operator watches it too.

India’s CEA (Central Electricity Authority) connectivity regulations count energy storage as a grid user. Users must provide on-line operational data such as voltage, frequency, line flows and breaker and isolator status, as the load despatch centre prescribes. They must also integrate their telemetry with the state and regional AGC (automatic generation control), EMS and SCADA systems. Our guide to CEA connectivity standards covers the wider rulebook.

The SECI specification puts this into the contract scope. It includes a telemetry system for sending plant data to the SLDC (state load despatch centre) and RLDC (regional load despatch centre), and requires SCADA to send any parameters they specify. It also calls for two-way communication with the RLDC for ancillary services and AGC. That link is what lets a battery earn from the frequency regulation services described elsewhere in our Knowledge Centre.

Protocols named in Indian tenders

Protocols are the languages devices use to exchange data. The SECI specification names:

  • Modbus over RS485 or Ethernet for field devices
  • Modbus TCP/IP for operator power setpoints and for grid-operator targets sent to the PPC
  • IEC 61850 for protection relays reporting to SCADA

The protocol for the link to the load despatch centre is not fixed in that document. The SLDC or RLDC issues its own interface specification. Confirm it early on every project, because it decides which gateway hardware you need.

Cyber security is part of the design

Every remote connection is also a possible way in. The SECI specification requires SCADA to comply with the CEA Cyber Security Guidelines, 2021.

In a 2024 interview, a CEA cyber security director said those guidelines led utilities to appoint chief information security officers, join CERT-In’s Cyber Swachhta Kendra, and run regular audits by CERT-In-empanelled auditors. For battery owners, that means network separation, access control and audit trails belong in the specification from day one. Our BESS cybersecurity guide goes further.

Commercial batteries: lighter, but the same logic

A factory or building battery, such as a C&I cabinet system, does not need utility-grade SCADA or load despatch centre telemetry. It normally has a local controller and a cloud portal showing state of charge, energy throughput, alarms and savings.

The questions are the same, just smaller. How often does it record data? Where is the data kept? What happens when the internet link drops? Who gets the alarm at 2 a.m.?

What this means for you

  • If you are writing a tender or RFP: put polling intervals, alarm latency, data retention, local buffering and time-sync in the specification as numbers, not adjectives. The SECI figures above are a sensible starting benchmark.
  • If you are bidding on a utility project: ask the SLDC or RLDC for its interface specification and cyber security requirements before you price the SCADA scope. For grid-scale builds like a 20ft container system or standalone BESS, this is often where late surprises come from.
  • If you own a commercial battery: check you can export your own data, that alarms reach a named person, and that data is buffered locally if the connection fails.
  • If you want a monitoring and controls package scoped for your site: talk to our team.

Technical requirements differ between tenders and are updated by CEA, SECI and the load despatch centres through new notifications and specifications. Treat this as a November 2026 snapshot and verify the current terms for your project before designing to them.

Frequently asked questions

Is SCADA the same as the EMS?

No. The EMS decides what the battery should do: when to charge, when to discharge, how much. SCADA is the supervisory layer that collects data from every device in the plant, shows it to operators, logs it, raises alarms and passes data to and from the grid operator. In smaller systems one software product may do both, but the functions are different.

Does a small commercial battery need SCADA?

Not a utility-grade one. A factory or building battery normally has a local controller plus a cloud monitoring portal that shows state of charge, energy throughput, alarms and savings. Full SCADA with load despatch centre telemetry is a requirement for grid-connected utility-scale plants.

Which communication protocols are used?

In the SECI specification we reviewed, Modbus (over RS485 or Ethernet) links field devices, Modbus TCP/IP carries power setpoints, and protection relays talk to SCADA using IEC 61850. The protocol for the link to the load despatch centre is set by the SLDC or RLDC itself, so it should be confirmed for each project.

What happens if the internet link goes down?

The plant keeps running on its local controllers. Good designs buffer data locally so nothing is lost. The SECI specification asks field controllers to store at least two weeks of data in case the network fails, and the plant server keeps its own long-term record independent of the cloud.

Let's talk storage

Want these numbers for your site?

Send a bill or a load profile — we model it and tell you straight.