Skip to content
NEXGY — Next Generation Energy

Technology

Can a battery storage system improve or worsen power quality and harmonics at a site?

Both. A battery system connects through a power electronic inverter, which can inject harmonics and cause resonance if it is poorly designed or filtered. The same inverter, properly specified and controlled, can supply reactive power, ride through voltage dips and actively cancel harmonics from other loads. The outcome depends on the design, the studies and the settings.

Published 16 November 2026 · Last updated 16 November 2026 · 5 min read · By NEXGY Research Desk

On this page

Most people judge a battery by how many kilowatt-hours it stores and how much it saves. Power quality rarely comes up until something goes wrong: a transformer runs hot, a drive trips, or the DISCOM complains about distortion at the meter.

A battery system can be part of that problem or part of the fix. Which one depends almost entirely on how its inverter is designed, studied and set up.

What “power quality” means

Power quality is how closely your supply matches the ideal: a steady voltage, at 50 Hz, with a clean sine-wave shape, balanced across the three phases. The common problems are:

  • Harmonics. Distortion of the sine wave at multiples of 50 Hz (150 Hz, 250 Hz and so on). Variable-speed drives, rectifiers, LED drivers, arc furnaces and inverters all create them.
  • Voltage dips and swells. Short drops or rises in voltage, often caused by faults on the network or large motors starting.
  • Poor power factor. Too much reactive power flowing, which loads cables and transformers without doing useful work and can attract DISCOM penalties.
  • Flicker and unbalance. Rapid voltage fluctuations and unequal loading across phases. These are common at steel plants. See BESS for cement, steel and energy-intensive industry.

Harmonics matter because they cause real damage: extra heating in transformers, cables and motors, nuisance tripping, and capacitor banks that fail early.

How a battery can make it worse

A battery stores DC (direct current) power. It reaches the AC (alternating current) grid through a power conversion system (PCS), an inverter that switches at high frequency. Our PCS explainer covers how it works. That switching produces some harmonic current, which the inverter’s filters are meant to keep within limits.

Problems tend to come from three places:

  • Weak filtering, especially in low-cost inverters.
  • Resonance. The inverter’s filter capacitors, the site’s cables, transformers and any power factor correction capacitors can combine to amplify a particular harmonic.
  • Weak grid connections, where the network is not strong enough to absorb what the inverter produces.

This is not a theoretical risk. A paper presented at the 2025 International Conference on Power Systems Transients (IPST) on a 50 MW battery in the UK reported harmonic non-compliances in measurements taken during and after commissioning. The lesson is that harmonic studies and site measurements need to be part of the project plan, not an afterthought.

How a battery can make it better

The same inverter that can cause problems is also a fast, flexible power electronic device. With the right rating and controls, it can:

  • Supply reactive power to correct power factor and support voltage, even when the battery is not charging or discharging.
  • Ride through and support voltage during dips, keeping sensitive loads running. With islanding, it can carry the site through an outage.
  • Balance phases by drawing or supplying different amounts of current on each phase.
  • Actively cancel harmonics from other loads by injecting equal and opposite harmonic currents. This is how an active harmonic filter works.

Commercial products already combine these functions. ABB’s PQpluS, for example, is a behind-the-meter battery system designed with built-in harmonic filtering, load balancing and reactive power compensation. Academic work points the same way: a study from the Universidad Nacional de Colombia found that charge and discharge control of a battery system can reduce total harmonic distortion (THD) at a connection point.

The catch is inverter capacity. Every kVA (kilovolt-ampere) used for reactive power or harmonic cancellation is a kVA not available for real power. If you want the battery to do both, size the PCS for it. Grid-supporting inverter controls are covered in grid-forming inverters.

Which limits apply in India

India’s grid connectivity rules refer to IEEE 519, the international standard for harmonic control, for harmonic limits. According to industry analysis of the CEA (Central Electricity Authority) connectivity regulations, the 2019 amendment linked voltage harmonic limits for distribution licensees and current harmonic limits for bulk consumers to IEEE 519 “as amended from time to time”. The current edition is IEEE 519-2022. Check your own connection agreement and your state’s supply code for the exact wording that applies to you.

IEEE 519 limit on total harmonic voltage distortion (THD)≤ 1 kV (LT supply)8.0%1–69 kV (11/33 kV)5.0%69–161 kV (110/132 kV)2.5%> 161 kV (220/400 kV)1.5%Voltage THD at the point of common coupling. Current limits vary with the site’s short-circuit ratio.
IEEE 519 voltage distortion limits fall as the connection voltage rises. Limits apply at the point of common coupling, so a battery's contribution adds to everything else on site.

Two points are easy to miss:

  • The limits apply at the point of common coupling, where your installation meets the utility network. Your battery’s harmonics add to your drives, rectifiers and other loads. A battery that is fine on its own can still push an already-distorted site over the limit.
  • Current limits depend on the strength of the grid at your site. IEEE 519 scales them by the ratio of the available short-circuit current to your load current. A site on a weak feeder gets tighter current limits.

Utility-scale batteries also have to meet the CEA’s wider technical standards for connection. See CEA technical standards for connecting a battery.

What to put in your specification

  • A harmonic limit at the point of common coupling, referencing IEEE 519 or your connection agreement, plus an inverter-level current distortion figure declared by the supplier.
  • A harmonic and resonance study before final design, using your site’s actual network, transformers and capacitor banks.
  • Power quality measurements before installation and after commissioning, using a recognised method such as IEC 61000-4-30, so you can see what changed.
  • Reactive power and voltage support capability stated in kVAr, and whether it is available when the battery is idle.
  • Harmonic cancellation, if you want it, as a named function with a stated capacity, not a vague “power quality support” line.

Our BESS purchase specification checklist shows where these sit in a full specification.

What this means for you

  • If you run a factory with drives, furnaces or rectifiers: measure your power quality first. If harmonics or voltage dips are already a problem, a battery with the right inverter controls can do peak shaving and power quality correction from the same hardware, but only if it is sized and specified for both.
  • If you are adding storage to a solar plant or substation: budget for harmonic and resonance studies and post-commissioning measurements. Grid-side services like voltage and reactive power support are covered in grid stabilisation.
  • If you are comparing suppliers: ask each one for their inverter’s declared harmonic current distortion, their filter design and evidence from a measured site. Systems such as our C&I cabinet should come with this data.
  • If you want to see what storage could save on your bills first: try our BESS savings calculator, or contact our engineering team for a power quality review.

Grid connection standards and state supply codes change by notification. Treat this as a November 2026 snapshot and confirm the harmonic limits in your own connection agreement and the current CEA regulations.

Frequently asked questions

What is total harmonic distortion (THD)?

THD expresses all the harmonic content of a voltage or current as a percentage of the normal 50 Hz component. A perfect sine wave has 0% THD. Higher numbers mean a more distorted waveform, which causes extra heating and can make protection and electronic equipment misbehave.

Will a battery fix my power factor penalty?

It can help, because a modern battery inverter can supply reactive power while it charges, discharges or idles. Whether it replaces your existing capacitor bank depends on the inverter's kVA rating and how much of that rating you want to keep free for real power.

Is a battery a substitute for an active harmonic filter?

Sometimes, but not by default. Harmonic cancellation needs specific controls and spare inverter capacity. If harmonics are your main problem, compare the cost of a dedicated active filter with paying for a battery inverter that can do both jobs.

Where are harmonic limits measured?

At the point of common coupling, which is the point where your installation meets the utility network. Limits apply to the combined effect of everything on your side of that point, not to each machine separately.

Let's talk storage

Want these numbers for your site?

Send a bill or a load profile — we model it and tell you straight.